No full-text available
To read the full-text of this research,
you can request a copy directly from the authors.
Rapid polymerization of polyhedral oligomeric siloxane-based zwitterionic sulfoalkylbetaine monolithic column in ionic liquid for hydrophilic interaction capillary electrochromatography
Abstract
A novel polyhedral oligomeric siloxane (POSS)-based zwitterionic monolithic capillary column was prepared via one-pot polymerization in ionic liquid porogen, using N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl)ammonium betaine (DMMSA) and methacrylic ethyl trimethylammonium chloride (META) as binary functional monomers, and methacryl substituted POSS as cross-linker. The pore structure, permeability and homogeneity were well tuned by optimizing the polymerization conditions. The resultant monolith was characterized by scanning electron microscopy, nitrogen adsorption/desorption isotherm and Fourier transform infrared spectroscopy. The incorporation of zwitterionic ligand (DMMSA), quaternary amine group (META) and rigid POSS skeleton endows the hybrid organic-silica monolith with high hydrophilicity, electrostatic interaction and good mechanical stability, as well as a tunable electroosmotic flow over wide pH range. A close investigation of capillary electrochromatographic separations of different types of polar compounds such as bases, nucleosides and benzoic acids on such stationary phase exhibited a retention independent column efficiency up to 118,000 plates/m (thiourea), as well as a mixed-mode hydrophilic interaction chromatography (HILIC) retention mechanism including weak electrostatic interaction, hydrophobic interaction and anion exchange.
... (Lei et al., 2020) prepared IL monolithic columns by grafting 2-methacryloyloxyethyl phosphorylcholine (MChoP) onto ILs (as shown in Figure 3A), to provide a hydrophilic surface for the stationary phase, while the IL also reduces the defect of poor overall column stability. In some reports, polyhedral oligomeric siloxane (POSS) was introduced into the IL monolithic column (as shown in Figure 3B) to improve the mechanical stability and pH tolerance of the column (Shan et al., 2015;Huang et al., 2021). ...
The chromatographic column is the core of a high-performance liquid chromatography (HPLC) system, and must have excellent separation efficiency and selectivity. Therefore, functional modification materials for monolithic columns have been rapidly developed. This study is a systematic review of the recently reported functionalized monolithic columns. In particular, the study reviews the types of functional monomers under different modification conditions, as well as the separation and detection techniques combined with chromatography, and their development prospects. In addition, the applications of functionalized monolithic columns in food analysis, biomedicine, and the analysis of active ingredient of Chinese herbal medicines in recent years are also discussed. Also reviewed are the functionalized monolithic columns for qualitative and quantitative analysis. It provided a reference for further development and application of organic polymer monolithic columns.
... For instance, chiral chromatography combines the principles of size exclusion and affinity-based separation. Electrochromatography (EC) [18][19][20], widely used to separate proteins and DNA, combines size and electrostatic separation principles. Separation in EC is based on the ratio of the charge density of the compounds. ...
Compound separation plays a key role in producing and analyzing chemical compounds. Various methods are offered to obtain high-quality separation results. Liquid chromatography is one of the most common tools used in compound separation across length scales, from larger biomacromolecules to smaller organic compounds. Liquid chromatography also allows ease of modification, the ability to combine compatible mobile and stationary phases, the ability to conduct qualitative and quantitative analyses, and the ability to concentrate samples. Notably, the main feature of a liquid chromatography setup is the stationary phase. The stationary phase directly interacts with the samples via various basic mode of interactions based on affinity, size, and electrostatic interactions. Different interactions between compounds and the stationary phase will eventually result in compound separation. Recent years have witnessed the development of stationary phases to increase binding selectivity, tunability, and reusability. To demonstrate the use of liquid chromatography across length scales of target molecules, this review discusses the recent development of stationary phases for separating macromolecule proteins and small organic compounds, such as small chiral molecules and polycyclic aromatic hydrocarbons (PAHs).
In this study, a poly (IL@MOF) composite monolithic column was synthesized using a simple and easy method. By adjusting the ratio of monomers, porogenic agents and cross‐linking agents, a macroporous composite monolith composed of metal organic framework (MOF) and ionic liquids (IL) was constructed. It was used as a high‐performance solid phase extraction (SPE) sorbent for the extraction of acacetin from medicinal and food homologous plants. The proposed SPE‐HPLC method for determination of acacetin had the advantages of high precision (0.06∼1.00 %), wide linear range (0.01∼250 μg mL⁻¹) and low detection limits (3.26 ng mL⁻¹). The poly (IL@MOF) monolithic column had excellent repeatability as an adsorbent. After 300 adsorption/desorption cycles, the corresponding chromatographic signal had no obvious change. These results indicated that the poly (IL@MOF) composite monolithic column was an ideal adsorbents and that the proposed method had potential for the enrichment and purification of flavonoids from medicinal and food homologous plants.
A method for the preparation of ploy(N‐vinylpyrrolidone‐co‐pentaerythritol triacrylate copolymerization)‐based monolithic capillary column was reported for the separation of polar small molecular weight compounds with nano‐liquid chromatography in hydrophilic interaction chromatography mode. The monolithic columns were prepared by in situ copolymerization of N‐vinylpyrrolidone and a cross‐linker pentaerythritol triacrylate in a binary porogenic agent consisting of methanol and water. The composition of the polymerization solution was systematically optimized in terms of column permeability, theoretical plate number, asymmetric factor, and retention factor. A typical hydrophilic chromatography retention mechanism was observed with mobile phase composed of the high content of organic solvent. The preparation method is simple and robust, the precursor N‐vinylpyrrolidone is chemically stable, cheap and easily available. The N‐vinylpyrrolidone‐based hydrophilic interaction chromatography stationary phase displays satisfactory separation selectivity for a range of polar test analytes, including benzoic acid derivatives, nucleosides and phenols. This article is protected by copyright. All rights reserved
A monolithic-based mixed-mode stationary phase was prepared for capillary electrochromatography via the fast photoinitiated polymerization of 2-methacryloyloxyethyl phosphorylcholine and polyhedral oligomeric silsesquioxane methacrylate (POSS-MA) monomers in the presence of crosslinker pentaerythritol triacrylate (PETA). Several copolymerization parameters, including the composition of monomers or porogens, ratio of crosslinkers to monomers, and polymerization time, were systematically optimized to tune the permeability and efficiency of monolithic columns. The morphologies and structures of the as-prepared monoliths were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, thermogravimetry and nitrogen adsorption/desorption analysis, indicating a typical POSS skeleton morphology with numerous mesopores on the monolith. Owing to the incorporation of zwitterionic functional groups and rigid POSS skeleton on the hybrid monolith, the resulting stationary phase exhibited both hydrophilic and electrostatic interactions, as well as good mechanical stability. Pressurized CEC separation of various kinds of polar compounds such as amides, nucleobases, nucleosides and benzoic acids, and polypeptide antibiotics was achieved by mixed-mode retention mechanisms including hydrophilic interaction chromatography (HILIC) and weak cation exchange chromatography (WCX) with a high column efficiency up to 93 500 plates per m (thiourea).
An in-situ approach is described for synthesis of poly(sulfobetaine-co-polyhedral oligomeric silsesquioxane) [poly(sulfobetaine-co-POSS)] that can be used in a hybrid monolithic column as a hydrophilic liquid chromatography (HILIC) stationary phase. Synthesis involves (a) radical polymerization of octa(propyl methacrylate)-polyhedral oligomeric silsesquioxane (MA-POSS) and organic monomers such as dimethylaminopropyl methacrylate or vinyl imidazole, and (b) in-situ ring-opening quaternization between 1,4-butane sultone and the organic monomers. The sulfobetaine groups are generated in-situ monolith. This obviates the need for synthesis of sulfobetaine monomer previously. The pore size and permeability of the material can be tuned by using a binary porogenic system (polyethyleneglycol 600 and acetonitrile) and via the composition of the polymerization mixture. The optimized hybrid monolith owns its merits to the presence of POSS and sulfobetaine groups with good mechanical stability, the lack of residual silanol groups, and adequate hydrophilicity. The column filled with the monoliths was evaluated as a stationary phase for HILIC. Several kinds of polar compounds (including nucleosides, bases, phenols, aromatic acids and amides) were separated by using mobile phases with high organic solvent fractions in capillary liquid chromatography.
A series of amphiphilic macroporous mixed-mode acrylamide-based continuous beds bearing positively charged quaternary ammonium groups is synthesized for capillary electrochromatography (CEC) under variation of the concentration of the cationic monomer in the polymerization mixture. Positively charged mixed-mode monolithic stationary phases are synthesized in pre-treated fused silica capillaries of 100 µm I.D via single step free radical copolymerization of cyclodextrin-solubilized N-tert-butylacrylamide, a hydrophilic crosslinker (piperazine diacrylamide), a hydrophilic neutral monomer (methacrylamide), and a positively charged monomer ([2-(methacryloyloxy)ethyl]trimethyl ammonium methyl sulfate) in aqueous solution containing the lyotropic salt ammonium sulfate as a pore-forming agent. The synthesized monolithic stationary phases contain hydrophobic, hydrophilic, and charged functionalities. They can be employed for the CEC separations of different classes of neutral and charged solutes (with varied polarity) in the reversed-phase mode, in the normal-phase mode, in the ion-exchange mode, in a mixed-mode, or in the hydrophilic interaction liquid chromatography (HILIC) mode. The influence of the concentration of the cationic monomer in the polymerization mixture on retention factor, electroosmotic mobility, and methylene selectivity (αmeth) is studied under isocratic conditions for alkylphenones in the reversed-phase mode by capillary electrochromatography (CEC). Scanning electron microscopy (SEM) micrographs demonstrate that the morphology of the synthesized monoliths (i.e., the domain size) is strongly influenced by the variation of the concentration of the cationic monomer in the polymerization mixture.
A methacrylate based monolith, containing the innovative zwitterionic monomer (3-allyl-1-imidazol)propane sulfonate, was prepared in 100 μm I.D. silica capillaries by UV initiated photo-polymerisation. Composition of the porogen, i.e. a mixture of 1-propanol, 1,4 butanediol and water, was of great importance to obtain a homogeneous monolith with satisfactory permeability and good electrochromatographic performance. Morphology of the stationary phase was studied in Scanning Electron Microscopy and IR experiments, which revealed a good attachment to the capillary wall, flowthrough-pores in the range of 0.5 to 2 μm, and a continuous monolithic structure. The developed material was well suited for the analysis of six common phenolic acids (salicylic, cinnamic, syringic, rosmarinic, caffeic and chlorogenic acid) by CEC. Their separation was possible in less than 8 min with a mobile phase comprising a 12 mM aqueous ammonium acetate solution with pH 8.5 and acetonitrile, at an applied voltage of - 20 kV. The developed method was validated (R² ≥ 0.995; LOD ≤ 3.9 μg mL⁻¹, except for salicylic acid; recovery rates from 94 to 104 %) and successfully used for the determination of phenolic acids in Coffea arabica samples. All of them contained cinnamic, syringic and caffeic acid, however only in unroasted coffee beans chlorogenic acid (0.06 %) was found. The quantitative results were in good agreement to reported literature data.
Polyethylenimine (PEI) and 2,4,6,8-tetramethyl-2,4,6,8-tetrakis(propyl glycidyl ether)cyclotetrasiloxane (POSS–epoxy) were used as precursors for the preparation of organic-silica hybrid monolithic columns (PEI–POSS monolith) via epoxy–amine ring-opening polymerization (ROP). The high density of amine groups in PEI provides rich chromatographic interaction sites for the polar or acidic analytes in hydrophilic interaction (HILIC) and weak anion exchange (WAX) mechanisms. The column preparation conditions, such as the porogens, solvent and reaction temperature, were systematically investigated according to the morphology, permeability and column efficiency. The separation mechanisms of HILIC and WAX were evaluated with neutral polar compounds and halogen benzoic acids. Owing to the existence of reactive amine groups on the matrix surface, the PEI–POSS monolith is also an ideal starting material for the preparation of HILIC or strong anionic exchange (SAX) stationary phases by modification. The modification of PEI–POSS monoliths with iodomethane or bromoacetic acid via the nucleophilic substitution reaction could achieve the retention mechanisms of SAX or zwitterionic HILIC, respectively.
The currently most successful type of porous polymer monoliths utilized in chromatography is prepared by free-radical cross-linking (co)polymerization in porogenic solvents and a single-step molding process. Though such types of materials are well-recognized in the scientific community, they suffer from their multi-scale heterogeneity originating from the nanoscale through to their microscale and ultimately limited performance on their macroscale. This is in particular true when estimating their performance under equilibrium (i.e. isocratic) elution conditions for retained compounds.
A novel "one-pot" approach was developed for ultra-rapid preparation of various hybrid monolithic columns in the UV-transparent fused-silica capillaries via photo-initiated thiol-acrylate polymerization of an acrylopropyl polyhedral oligomertic silsesquioxane (acryl-POSS) and a mono-thiol monomer (1-octadecanethiol or sodium 3-mercapto-1-propanesulfonate) within 5 minutes, in which the acrylate not only homopolymerizes, but also couples with the thiol. This unique combination of two types of free-radical reaction mechanisms offers a simple way to fabricate various acrylate-based hybrid monoliths. The physical characterization, including SEM, FT-IR and thermal gravimetric analysis was performed. The results indicated that the mono-thiol monomers were successfully incorporated into acryl-POSS based hybrid monoliths. The column efficiencies for alkylbenzenes on the C18-functionalized hybrid monolithic column reached to 60,000-73,500 plates per meter at the velocity of 0.33 mm/s in capillary liquid chromatography, which was far higher than that of previously reported POSS-based columns prepared via thermal-initiated free-radical polymerization without adding any thiol monomers. By plotting of plate height (H) of alkylbenzenes versus the linear velocity (u) of mobile phase, the results revealed a retention-independent efficient performance of small molecules in the isocratic elution. These results indicated that more homogeneous hybrid monoliths formed via photo-initiated thiol-acrylate polymerization, particularly, the use of multi-functional crosslinker possibly prevented the generation of gel-like micropores, reducing mass transfer resistance (C-term). Another sulfonate-containing hybrid monolithic column also exhibited hydrophobicity and ion-exchange mechanism, and the dynamic binding capacity was calculated as 71.1 ng/cm (75 μm i.d.).
Low column efficiency for small molecules in reversed-phase chromatography is a major problem commonly encountered in polymer-based monoliths. Herein, a novel highly crosslinked porous polymeric monolith was in situ prepared by using a multi-acrylate monomer, dipentaerythritol penta-/hexa-acrylate (DPEPA), as crosslinker, which copolymerized with lauryl methacrylate (LMA) as functional monomer in a UV-transparent fused-silica capillary via photo-initiated free-radical polymerization within 5min. The mechanical stability and permeability of the resulting poly(LMA-co-DPEPA) monolith were characterized in detail. One series of highly crosslinked poly(LMA-co-DPEPA) columns were prepared with relatively higher content of crosslinker (63.3%) in the precursor. Although they exhibited lower permeability, high column efficiency for alkylbenzenes was acquired in cLC, and the minimum plate height (column B) was in the range of 6.04-9.00μm, corresponding to 111,000-165,000Nm(-1). Meanwhile, another series of poly(LMA-co-DPEPA) columns prepared with relatively lower content of crosslinker (52.7%) in the precursor exhibited higher permeability, but the minimum plate height (column E) was relatively low in the range of 10.75-20.04μm for alkylbenzenes, corresponding to 50,000-93,000Nm(-1). Compared with common poly(LMA-co-EDMA) columns previously reported, the highly crosslinked poly(LMA-co-DPEPA) columns using a multi-acrylate monomer as crosslinker possessed remarkably high column efficiency for small molecules in cLC. By plotting of plate height (H) of alkylbenzenes versus the linear velocity (u) of mobile phase, the results revealed a retention-independent efficient performance of small molecules in the isocratic elution, indicating that the use of multi-functional crosslinker possibly prevents the generation of gel-like micropores in the poly(LMA-co-DPEPA) monolith, reducing the mass transfer resistance (C-term).
Copyright © 2015 Elsevier B.V. All rights reserved.
In this communication, we report a very efficient method of manufacturing polymer-based monolith in an ionic liquid reaction medium via microwave-assisted vinylization and polymerization. This novel approach took only 10 min to complete the whole process.
A silica based amino stationary phase was prepared by immobilization of propargylamine on azide-silica via click chemistry. This readily prepared click amino stationary phase demonstrated good selectivity in separation of common inorganic anions under ion chromatography (IC) mode, and the triazole ring in combination with free amino group was observed to play a major role for separation of the anions examined. On the other hand, the stationary phase also showed good hydrophilic interaction liquid chromatography (HILIC) properties in the separation of polar compounds including nucleosides, organic acids and bases. The retention mechanism was found to match well the typical HILIC retention.
Magnetic field effects (MFEs) on the photoinduced hydrogen abstraction reaction of benzophenone with phenol were investigated in ionic liquids (ILs) with a short alkyl chain (N,N,N-trimethyl-N-propylammonium bis(trifluoromethanesulfonyl)amide (TMPA TFSA)) and long alkyl chains ((N,N,N-trimethyl-N-octylammonium bis(trifluoromethanesulfonyl)amide (TMOA TFSA) and N-decyl-N,N,N-trimethylammonium bis(trifluoromethanesulfonyl)amide (DTMA TFSA)) by a nanosecond laser flash photolysis technique. In each ionic liquid, escaped radical yield of a benzophenone ketyl radical rapidly increased with increasing magnetic field strength (B) of 0 T < B≤ 0.01 T. At 0.01 T < B≤ 0.4 T, the escaped radical yield almost saturated in TMPA TFSA or gradually increased in TMOA TFSA and DTMA TFSA. At much higher fields of 0.4 T < B≤ 30 T, the yield gradually decreased, resulting in 10-15% decrease at 30 T. The observed MFEs can be explained by the hyperfine coupling and Δg mechanisms together with the relaxation mechanism. On the time profiles of the transient absorption observed for the benzophenone ketyl radical, MFEs were generated in the time range of 0 < t < 0.6 μs. The cage lifetimes of TMOA TFSA and DTMA TFSA were estimated to be at least 120 ns.
Porous polymer monoliths have emerged as unique materials for many applications, including liquid-chromatographic analyses at an unrivaled speed, solid-phase extraction, and enzyme immobilization in capillary and microfluidic chip format. This article reviews the state of the art in the preparation of monoliths in narrow-bore capillaries and microfluidic chips and their miniaturization under conditions of spatial confinement. New developments in their preparation mainly using free radical polymerization techniques with a focus on morphological aspects in view of homogeneous porous materials are described. The suitability of monoliths for analysis of both large and small molecules is also discussed.
Based on its “lock-key theory”, molecular imprinting technique (MIT) has received extensive attention and obtained huge development. Because of their highly tunable nature and outstanding physicochemical properties, ionic liquids (ILs) as a promising substance class have obtained in-depth investigation and been widely utilized in various fields. The combination of MIT and ILs can not only enlarge research and application scope of ILs, but also well deal with some shortcomings and challenges of MIT. In this review, we will comprehensively summarize the related works about molecularly imprinted polymers incorporating with ionic liquids (IL-MIPs) and their application in solid-phase extraction (SPE). During the preparation of IL-MIPs, ILs take on different roles, sorting into single role (functional monomer, porogen, stabilizer, cross-linker, etc.) and dual/multiple role (monomer-stabilizer, monomer-cross linker, monomer-template, surface modifier-monomer, etc.). The application of IL-MIPs as SPE adsorbents will be discussed from the point of extraction form (off-line SPE and on-line SPE). In the end, the challenges and future outlook about this topic will also be discussed.
Abscract
Allylglycine, a conventional amino acid derivative, possesses typical zwitterionic and hydrophilic functionalities deriving from the carboxyl and amino groups in its structure. A novel monolithic column poly(allylglycine-co-1, 3, 5-triacryloylhexahydro-1, 3, 5-triazine) (AGly-co-TAT) with powerful hydrophilic selectivity and obvious zwitterionic feature was synthesized successfully with the monomer allyglycine and the cross-linker 1, 3, 5-triacryloylhexahydro-1, 3, 5-triazine through in-situ copolymerization for capillary electrochromatography. The obtained monolithic column has good permeability. Due to the zwitterionic functional groups of allylglycine, the poly(AGly-co-TAT) monolithic column can generate a cathodic and anodic electroosmotic flow (EOF) by changing the mobile phase pH, which is beneficial to expand its application range. The separations of different series of polar analytes, thioureas, xanthines, phenols, peptides and acidic compounds are achieved on this hydrophilic monolithic column due to the powerful hydrophilic, electrostatic and hydrogen bond interactions. Using this monolithic column, hydrophilic separations are achieved even at a lower level of 50% organic solvent. The separation efficiency up to 1.41 × 10⁵ N m⁻¹ and 1.19 × 10⁵ N m⁻¹ is achieved for the separation of theophylline and phenol, respectively. For a real sample, cytochrome C digestion, the monolithic column shows good separation performance, which offers the potential application of the monolithic column on proteomics study.
An ionic liquid hybrid zwitterionic polymer capillary microextraction (CME) column was prepared for the biomimetic enrichment of glycopeptides by one-step copolymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC) and 1-butyl-3-vinylimidazolium bromide, in the presence of crosslinker trimethylolpropane trimethacrylate (TMA). The resultant monolith was characterized by scanning electron microscopy (SEM), fourier transform infrared (FT-IR) spectroscopy and pore size distribution measurement. Due to the incorporation of zwitterionic MPC owning a unique biomimic structure (i.e. hydrophilic cation/anion and hydrophobic long-alkyl chain), the monolithic column has large pore size and good biocompatibility, exhibiting high extraction efficiency, permeability and fast mass transfer to targets. Besides, the use of ionic liquids (ILs) as co-monomer in the polymerization endows the monolith with enhanced mechanical stability, uniformity and multiple interactions. The prepared column was successfully applied in CME coupled to capillary electrochromatography (CEC) for the efficient enrichment and separation of glycopeptide antibiotics in foodstuff. The method demonstrated a wide linear range (50.0–18000.0 µg L⁻¹), low detection limits (5.0–10.0 µg L⁻¹, S/N=3) and satisfied recoveries (76.0–109.7 %). This work shows the advantage of fine-tuning biomimetic monoliths in application-specific CME-CEC.
Peptide retention time prediction models have been developed for zwitter-ionic ZIC-HILIC and ZIC-cHILIC stationary phases (pH 4.5 eluents) using proteomics-derived retention datasets of ~30 thousand tryptic peptides each. Overall, hydrophilicity of these stationary phases was found to be similar to the previously studied Amide HILIC phase, but lower compared to bare silicas. Peptide retention is driven by interactions of all charged (hydrophilic) residues at pH 4.5 (Asp, Glu, Arg, Lys, His), but shows specificity according to orientation of functional groups in zwitter-ionic pair. Thus, ZIC-cHILIC exhibits an increased contribution of negatively charged Asp and Glu due to the distal positioning of positively charged quaternary amines on the stationary phase. These findings confirm that HILIC interactions are driven by both peptide distribution between water layer adsorbed on the stationary phase and by interactions specific to functional groups of the packing material. Sequence-Specific Retention Calculator HILIC models were optimized for these columns showing 0.967-0.976 R2-values between experimental and predicted retention values. ZIC-HILIC separations represent a good choice as a first dimension in 2D LC-MS of peptide mixtures with correlations between retention values of ZIC-HILIC against RPLC found at 0.197 (ZIC-HILIC) and 0.137 (ZIC-cHILIC) R2-values, confirming a good orthogonality.
A novel monolithic column based on the copolymerization of ethylene dimethacrylate and a deep eutectic solvent (DES), which composed of chlorocholine chloride and itaconic acid, was developed for capillary electrochromatography (CEC). The structure and morphology of the obtained monolithic column was characterized by Fourier transform infrared spectra and scanning electron microscopy, which showed a porous monolithic structure with good permeability. The influence of pH value and acetonitrile content on electroosmotic flow (EOF) of DES-based monolithic column was investigated. The DES-based monolithic column was used as the separation column of CEC and exhibited excellent performance for the separation of neutral compounds, phenols, toluidines, nucleosides, nucleotide bases and alkaloids. The retention mechanism might be attributed to synergistic effect of hydrophobic interaction, hydrogen bond interaction and electronic interaction. The DES-based monolithic column showed good repeatability with relative standard deviations of migration time less than 0.80%, 2.15%, 4.26% and 3.08% for intra-day, inter-day, column-to-column and batch-to-batch, respectively. Thus, organic polymer monolithic columns with DESs as functional monomers are a promising option in chromatographic separation.
Through introducing octakis (3-mercaptopropyl) octasilsesquioxane (POSS-SH) synthesized in our lab to the prepolymerization solution containing stearyl acrylate (SA), 1,6-hexanediol ethoxylate diacrylate (HEDA) in the existence of porogenic solvents (tetrahydrofuran, 1,4-butanediol and 1-propanol), a POSS-containing hybrid monolithic column was fabricated via photo-initiated thiol-acrylate polymerization within 7 min. The resulting poly(SA-co-HEDA-co-POSS) monoliths were investigated by physical characterization and chromatographic evaluation. It was found that both the additive amount of thiol group and the proportion of porogenic solvents played vital effect on column efficiency, pore morphology and hydrophobicity of monolithic columns. Consequently, the poly(SA-co-HEDA-co-POSS) monolith possessed superior thermal stability, suitable permeability and homogeneous microstructure. The highest column efficiency was ∼111,000 N m⁻¹ for butylbenzene at the linear velocity of 0.71 mm s⁻¹ in reversed-phase liquid chromatography. Subsequently, baseline separations of 9 phenolic compounds, 5 anilines and 5 antibiotics were achieved, indicating the monolithic poly(SA-co-HEDA-co-POSS) column had great ability for separation of small molecules. The analytic results of the tryptic digest of BSA and HeLa were also proved that the hybrid monolith had potential for the analysis of complicated biological samples.
A reactive monolith based on the polymerization of 3‐chloro‐2‐hydroxypropyl methacrylate, (HPMA‐Cl), with a crosslinking agent, ethylene glycol dimethacrylate (EDMA), was synthesized and post‐functionalized with a macromolecular ligand polyethyleneimine. Monolithic columns with controlled permeability and pore structure were prepared by free radical polymerization in the presence of a binary porogenic mixture of isopropanol and decanol. The presence of chloropropyl functionality in the pristine monolith allowed the synthesis of a post‐fuctionalized monolith carrying cationic groups that was used to control the magnitude of electroosmotic flow (EOF) in electrochromatographic separation. In the synthesis of pristine monoliths, the feed concentration of functional monomer (ie, HPMA‐Cl) was changed between 30 and 60 v/v % for obtaining cationic monoliths providing satisfactory electrochromatographic separation. The best electrochromatographic performance was obtained with the polyethyleneimine functionalized monolith prepared by using the pristine monolith obtained by 60% (v/v) monomer concentration. This monolith was used in reversed phase and hydrophilic interaction capillary electrochromatography modes for the separation of alkylbenzenes, polycyclic aromatic hydrocarbons, phenols, and nucleosides, using mobile phases with low acetonitrile (ACN) contents ranging between 20% and 35% (v/v). This ACN range was remarkably lower than the content of ACN used on the hydrophilic polymethacrylate‐based monoliths reported previously (ie, >90%). The plate heights up to 5.3 μm were obtained for the separation of nucleosides with the environmental friendly mobile phases whose ACN contents were also remarkably lower than that of similar polymethacrylate‐based monoliths.
Although several approaches have been developed to fabricate hybrid monoliths, it would still take a few hours to finish the formation of monoliths. Herein, photo-initiated thiol-yne polymerization was first adopted to in situ fabricate hybrid monoliths within the confines of UV-transparent fused-silica capillary. A silicon-containing diyne (1,3-diethynyltetramethyl-disiloxane, DYDS) was copolymerized with three multithiols, 1,6-hexanedithiol, trimethylolpropane tris(3-mercaptopropionate) and pentaerythriol tetrakis(3-mercaptopropionate), by using a binary porogenic system of diethylene glycol diethyl ether (DEGDE)/poly(ethylene glycol) (PEG200) within 10 min. Several characterizations of three hybrid monoliths (assigned as I, II and III, respectively) were performed. The results showed that these hybrid monoliths possessed bicontinuous porous structure, which was remarkably different from that via typical free-radical polymerization. The highest column efficiency of 76,000 plates per meter for butylbenzene was obtained on the column I in reversed-phase liquid chromatography (RPLC). It was observed that the efficiencies for strong-retained butylbenzene were almost close to those of weak-retained benzene, indicating a retention-independent efficient performance of small molecules on hybrid column I. The surface area of this hybrid monolith was very small in the dry state (less than 10.0 m2/g), and the chromatographic behavior of hybrid monolithic columns would be possibly explained by radical-mediated step-growth process of thiol-yne polymerization. Finally, the column I was applied for separation of BSA tryptic digest by cLC-MS/MS, indicating satisfactory separation ability for complicated samples.
The general dispersion theory of Aris is applied to predict the virtual asymptotic dispersion behavior of packed columns. The derived model is also used to estimate the actual pre-asymptotic dispersion behavior of modern 2.1 mm × 50 mm columns packed with sub-2 μm fully porous particles (FPPs) during the transient dispersion regime. The model accounts for the actual radial distribution of the flow velocity across the column diameter. From the wall to the center of the column, focused-ion-beam scanning electron microscopy (FIB-SEM) experiments were recently performed to reveal the existence of a thin (0.15dp wide, dp is the average particle diameter) hydrodynamic boundary layer (THBL), a thin (3dp wide) and loose orderly packed layer (TLOPL), a 60dp wide and dense randomly packed layer (WDRPL), and a large (≃460dp) randomly packed bulk central region [1]. The theoretical calculations of the actual pre-asymptotic reduced van Deemter curves (2.1 mm × 50 mm column, sub-2 μm BEH-C18 FPPs, n-hexanophenone analyte, acetonitrile/water eluent, 80/20, v/v, flow rate from 0.05 to 0.35 mL/min) confirm that the impact of the sole THBL on column dispersion can be neglected. In contrast, the contribution of the TLOPL to the reduced plate height (RPH) is about 0.2 h unit at optimum reduced velocity. Most remarkably, the negative impact of the TLOPL on column performance may be fully compensated by the presence of the adjacent WDRPL if the depth of the velocity well were to be 5% of the bulk velocity. In actual 2.1 mm × 50 mm columns packed with sub-2 μm FPPs, this velocity depth is as large as 25% of the bulk velocity causing a significant RPH deviation of 0.7 h unit from the RPH of the bulk packing free from wall effects. Maximum column performance is expected for a reduction of WDRPL density. This suggests optimizing the packing process by finding the proper balance between the stress gradient across the WDRPL (responsible for the deep velocity well) and the friction forces between the packed particles (responsible for the rearrangement of the particles during bed consolidation). Past and recently reported RPH data support the theoretical insights: the stress gradient/particle friction balance in the WDRPL is better realized when packing superficially porous particles (SPPs) rather than FPPs in 2.1-4.6 mm i.d. columns (the RPH deviation is reduced to 0.4 h unit) or sub-2 μm particles in 100 cm × 75 μm i.d. capillaries combining high slurry concentrations and sonication (the RPH deviation is reduced to only 0.15 h unit).
In this work, a hybrid monolith incorporated with graphene oxide (GO) was prepared in the first time with binary green porogens of deep eutectic solvents (DESs) and room temperature ionic liquids (RTILs). GO was modified with 3-(trimethoxysilyl) propylmethacrylate (γ-MPS), and the resultant GO-MPS can be incorporated into poly (methacrylic acid-co-butylmethacrylate-co-ethylene glycol dimethacrylate) monoliths covalently. A hybrid monolithic column with high permeability and homogeneity can be achieved due to good dispersion of GO-MPS in the green solvents. The GO-MPS incorporated monolith was characterized by transmission electron microscopy, scanning electron microscopy, thermogravimetric analysis and nitrogen adsorption tests. The separation of small organic molecules of alkylphenones and alkylbenzenes was used to evaluate the performance of GO-MPS grafted monolith. The GO-MPS grafted monolith displayed the maximum column efficiency of 147,000 plates/m, about twice higher than the GO-free monolith. In addition, all of the retention and selectivity of small molecules of alkylphenones and alkylbenzenes increased due to the addition of GO-MPS. The results demonstrated that the use of DESs and RTILs is a powerful approach for the preparation of GO incorporated polymer monoliths. The monolith was further applied to the separation of tryptic digests from bovine serum albumin, and the result indicated its potential in the analysis of some complex samples.
As a natural molecular-level organic-silica hybrid particle, polyhedral oligomeric silsesquioxane (POSS) is a good choice for the preparation of new hybrid monolithic columns because of its ease of fabrication, ultrahigh column efficiency, and excellent separation selectivity. In this review, we summarize the recently reported POSS-based hybrid monolithic columns, especially those reported in the recent 5 years. These POSS-based hybrid monolithic columns are classified according to the reactive groups of POSS and the introduced organically functionalized reagents, emphasizing the preparation methods and further applications in capillary liquid chromatography.
The quest for higher column efficiency is one of the major research areas in polymer-based monolithic column fabrication. In this research, two novel polymer-based HILIC monolithic columns with 400 μm I.D. × 800 μm O.D. were prepared based on the thermally initiated co-polymerization of N,N-dimethyl-N-(3-methacrylamidopropyl)-N-(3-sulfopropyl) ammonium betaine (SPP) and ethylene glycol dimethacrylate (EDMA) or N,N’-methylenebisacrylamide (MBA). In order to obtain a satisfactory performance in terms of column permeability, mechanical stability, efficiency and selectivity, the polymerization parameters were systematically optimized. Column efficiencies as high as 142, 000 plates/m and 120, 000 plates/m were observed for the analysis of neutral compounds at 0.6 mm/s on the poly(SPP-co-MBA) and poly(SPP-co-EDMA) monoliths, respectively. Furthermore, the van Deemter plots for thiourea on the two monoliths were compared with that on a commercial silica based ZIC-HILIC column (3.5 μm, 200 Å, 150 mm × 300 μm I.D.) using ACN/H2O (90/10, v/v) as the mobile phase at room temperature. It was noticeable that the Van Deemter curves for both monoliths, particularly the poly(SPP-co-MBA) monolith, are significantly flatter than that obtained for the ZIC-HILIC column, which indicats that in spite of their larger internal diameters, they yield better overall efficiency, with less peak dispersion, across a much wider range of usable linear velocities. A clearly better separation performance was also observed for nucleobases, nucleosides, nucleotides and small peptides on the poly(SPP-co-MBA) monolith compared to the ZIC-HILIC column. It is particularly worth mentioning that these 400 μm I.D. polymer-based HILIC monolithic columns exhibit enhanced mechanical strength owing to the thicker capillary wall of the fused-silica capillaries.
A hybrid monolith exhibiting almost retention independent separation performance in hydrophilic interaction chromatography (HILIC) was obtained by one-pot photoinitiated thiol-methacrylate polymerization. Polyhedral oligomeric silsesquioxane containing methacrylate units (POSS-MA) was used as the main monomer and crosslinking agent, together with a hydrophilic ligand with two carboxyl groups, mercaptosuccinic acid (MSA) as the thiol agent and chromatographic ligand. The isocratic separation of nucleosides, nucleotides and organic acids on MSA attached-poly(POSS-MA) monolith was investigated in HILIC mode. The van-Deemter plots for obtained for nucleosides, nucleotides and benzoic acids clearly showed that there were two regions in each graph with two different slopes in the studied range of linear flow rate (i.e. 0.2-4.3 mm/s). The slope of plate height-linear velocity curve was so small in the low linear velocity region between 0.2-2.1 mm/s while the slope in high linear velocity region between 2.1-4.3 mm/s was so higher with respect to the first region. The van-Deemter plots sketched for all analyte grous used in HILIC mode obeyed this tendency Almost “retention independent plate height behavior” was demonstrated in HILIC, using nucleotides, nucleotides or benzoic acids as the analytes in the linear velocity range of 0.2-2.1 mm/s. This behavior was explained by the porous structure of the synthesized monolith facilitating the convective transport of analytes. The variation of plate height was not retention-independent within high linear velocity range (> 3.2 mm/s) when nucleosides were separated in HILIC mode.
A macroporous hydrophilic organic-silica hybrid monolithic column was synthesized via photoinitiated thiol-ene click polymerization reaction of 1-thioglycerol-modified polyhedral oligomeric vinylsilsesquioxane (vinylPOSS) and dithiothreitol (DTT) in a binary porogenic system consisting of tetrahydrofuran (THF) and dodecanol. 1-Thioglycerol was used to modify vinylPOSS in order to form a precursor with good solubility in the binary porogenic system. The influences of both the ratio of 1-thioglycerol/vinylPOSS and the porogenic solvents on the morphology and permeability of hybrid monoliths were studied in detail. The physical properties of hybrid monolith were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy and nitrogen adsorption/desorption measurement. The chromatographic performance was evaluated by separation of neutral polar compounds in capillary liquid chromatography (cLC). The resulting column possessed homogeneous macroporous structure and showed hydrophilic interaction liquid chromatography (HILIC) separation mechanism with high efficiency of 65,000Nm(-1) for formamide. Ultimately, the hybrid matrix was grafted with hydrazine groups and then exhibited the ability of glycopeptides enrichment.
The synthesis and characterization of large-bore silica-based monolithic capillary columns (0.32 mm × 150 mm) are presented. Columns were prepared by acidic hydrolysis of a mixture containing tetramethoxysilane (TMOS) and 1,2-bis(trimethoxysilyl)ethane (BTME) in different molar ratios in the presence of polyethylene glycol and urea. The monoliths were modified by zwitterionic monomer [2-(methacryloyloxy)ethyl]-dimethyl-(3-sulfopropyl)-ammonium hydroxide via 3-(trimethoxysilyl)propyl methacrylate. Prepared stationary phases were evaluated by scanning electron microscopy and chromatographic separation of nucleobases and their derivatives in the HILIC mode. The best chromatographic results were obtained with the column prepared from the reaction mixture containing BTME and TMOS in a 1:4 molar ratio. The permeability of such column reached 1.68 × 10⁻¹⁴ m² and the efficiency, expressed as a height equivalent of the theoretical plate, did not exceed 10.5 μm for the tested compounds. The columns were successfully applied to HILIC separation of native and labelled oligosaccharides and glycans released from bovine ribonuclease B and human immunoglobulin G.
• A brief explanation on how CEC works is provided.
• A deep review of the literature about CEC in food analysis is done.
• Relevant applications in the different CEC modes are discussed.
• Future trends in this field are debated.
Capillary electrochromatography (CEC) is a miniaturized technique which gathers the high separation efficiency of capillary electrophoresis and the selectivity of liquid chromatography, being a very interesting hybrid separation procedure. It requires a small amount of solvents and samples, having a high impact in the total cost of the analysis. For these reasons, CEC has aimed a relatively big potential, especially in the fields of pharmaceutics and biomedicine analysis. Nonetheless, food analysis has also been of interest for a considerable number of researchers who have focused their efforts in this direction. This review article shows a deep examination of the use of CEC in food safety and food quality, from the first application in 1997 to the present, commenting those with a higher impact or novelty.
A protocol using trifluoroacetic acid at a temperature of 60°C is developed for the adequate removal of the stationary phase of reversed-phase (RPLC) columns. This procedure allows studying the same column first under RPLC and subsequently under hydrophilic interaction chromatography (HILIC) conditions to isolate intrinsic differences between mass transfer properties in HILIC and RPLC from differences in packing quality. The established procedure allows for a complete removal of the stationary phase (confirmed by retention studies and thermogravimetry analyses) while leaving the structure of the packing unaffected (witnessed by an unchanged external porosity and pressure drop). Accurate plate height analysis comparing compounds at the same zone retention factor indicate a significant difference in reduced c-term (typically 40 to 80% larger under HILIC conditions), despite the columns otherwise being identical. Correcting for the known contributions of longitudinal diffusion (b-term) and mass transfer (cm- and cs-term) to focus on band broadening originating from eddy dispersion, similar strong differences are observed (differences of some h=0.3 up to 1.2). These findings show that the interior structure and retention mechanism of the particles have a very strong effect on the observed eddy dispersion, a factor typically ascribed to phenomena occurring outside the particles. This also implies that comparing the quality of packings of different particle types is virtually impossible without the availability of a sound model to correct for the intra-particle effect on the observed eddy-dispersion.
In order to investigate the effects of the crosslinker on the separation performance of polar zwitterionic sulfoalkylbetaine-type monolithic columns, three crosslinkers, i.e. 1,4-bis(acryloyl)piperazine (PDA), ethylene dimethacrylate (EDMA) and N,N'-methylenebisacrylamide (MBA), were copolymerized with the hydrophilic monomer N,N-dimethyl-N-acryloyloxyethyl-N-(3-sulfopropyl)ammonium betaine (SPDA). The chromatographic properties of the three hydrophilic sulfoalkylbetaine-type monolithic columns, including column efficiency, permeability, porosity and separation mechanism, were systematically compared using scanning electron microscopy or micro-HPLC. Good selectivity in micro-HPLC separations was achieved on all three monolithic columns. The results indicate that the polarity of sulfoalkylbetaine-type monolithic columns may be related to the polarity of the crosslinker, which further affects column selectivity and efficiency. A particularly high column efficiency (100,000 plates/m) was obtained on the novel poly(SPDA-co-PDA) monolithic column at a linear velocity of 1mm/s using thiourea as test analyte. A higher resolution was also observed for nucleobases, nucleosides and hydrophilic organic acids on this novel poly(SPDA-co-PDA) monolithic column compared to the other two columns.
Copyright © 2014 Elsevier B.V. All rights reserved.
A novel polymer-based monolith for high performance liquid chromatography was fabricated via atom transfer radical polymerization without the expensive complexing ligand, in which methyl methacrylate as monomer, vinyl ester resin as cross-linker, 1-butyl-3-methylimidazolium chloride/dodecanol as porogen, carbon tetrachloride as initiator and ferrous chloride as catalyst agent. Morphology of monoliths was studied by scanning electronic microscopy. Chemical groups of the monolith were assayed by infrared spectra method. The pore size distribution was determined by mercury porosimeter and nitrogen absorption-desorption. The monolith was used to separate lysozyme from chicken egg white in a short time with good resolution and reproducibility. The effects of pH and buffer concentration on elution have been investigated. In addition, the monolith was used to separate the mixture of protein (bovine serum albumin, papain and lysozyme) with good resolution.
In this work, new polythiol-functionalized macroporous monolithic polymethacrylate-polysiloxane composite materials are presented which can be useful substrates for highly efficient immobilization of (chiral) catalysts, chromatographic ligands, and other functional moieties by thiol-ene click reaction. Poly(glycidyl methacrylate-co-ethylene dimethacrylate) (poly(GMA-co-EDMA)) monoliths were coated with a poly-3-mercaptopropyl methylsiloxane (PMPMS) film and subsequently the polymer was covalently immobilized by formation of crosslinks via nucleophilic substitution reaction with pendent 2,3-epoxypropyl groups on the monolith surface. This monolith, though, showed similar levels of surface coverage as a reference monolith obtained by opening of the epoxide groups with sodium hydrogen sulfide. However, a 3-step functionalization by amination of the epoxy monolith, followed by its vinylation with allylglycidyl ether and subsequent thiolation by coating of a thin polythiol (PMPMS) film and crosslinking by click reaction furnished a monolith with more than 2-fold elevated thiol coverage. Its further functionalization with a clickable chiral quinine carbamate selector clearly documented the benefit of highly dense thiol surfaces for such reactions and synthesis of functional materials with proper ligand loadings. The new monoliths were chromatographically tested in capillary electrochromatography mode using N-3,5-dinitrobenzoyl-leucine as chiral probe and the capillary column with the monolith having the highest selector coverage, produced from the precursor with the most thiols on the surface, showed the largest separation factor. By performic acid oxidation the surface characteristic could be tuned and strongly altered due to a delicate balance of enantioselective and non-specific interactions
Ionic liquids are attractive solvents for polymer synthesis because their properties can be easily and broadly tuned by varying the structure of both the cation and the anion. Application of ionic liquids as reaction medium for free radical polymerization of vinyl monomers, such as methacrylates or styrene, results in high yields and high molecular weights of the polymers. Reasons for these effects are only partially due to the high viscosity of ionic liquids, which may reduce bimolecular termination of the propagating chains, but are also due to solvent cage effects that differ from those in traditional organic solvents because of strong ionic interactions between the individual ions of the ionic liquids. Furthermore, the high dissolving power of ionic liquids for both weakly polar as well as highly polar monomers makes ionic liquids interesting as solvents for statistical copolymerization. Interestingly, variation of the alkyl chain length of substituents at the cation of the ionic liquid allows altering of copolymer composition.
Thermal analysis and SEM were employed to gain insights in the different stages of morphology development and the thermal properties of polymer-monolithic stationary phases. The studied system was a thermally initiated free-radical copolymerization reaction at 70°C of styrene and divinylbenzene in the presence of tetrahydrofuran and 1-decanol. The key events in the early stages of morphology development are initiation, chain growth, branching, and cyclization, leading to microgel particles. Interparticle reactions through pendant vinyl groups lead to the formation of microgel clusters. The rapid increase in molecular weight and crosslink density of the microgel clusters causes a reaction-induced phase separation, and the formation of a macroscopic network of interconnected globules was observed (macrogelation) at around 45 min. After 3 h or 65% conversion, a space-filling macroporous monolithic network was observed. Afterwards, mainly growth of existing globules takes place, reducing the macropore size. The porogen ratio affects the timing of the reaction-induced phase separation, strongly influencing the morphology of the polymer material. The use of a mixture of divinylbenzene isomers yielded a monolithic material that is less crosslinked at the surface compared to the central part of the polymer backbone due to copolymerization-composition drift. The less crosslinked outer layer starts devitrifying at 100°C. This article is protected by copyright. All rights reserved.
A new organic-inorganic hybrid monolith was prepared by the ring-opening polymerization of octaglycidyldimethylsilyl polyhedral oligomeric silsesquioxane (POSS) with 1,4-butanediamine (BDA) using 1-propanol, 1,4-butanediol, and PEG 10 000 as a porogenic system. Benefiting from the moderate phase separation process, the resulting poly(POSS-co-BDA) hybrid monolith possessed a uniform microstructure and exhibited excellent performance in chromatographic applications. Neutral, acidic, and basic compounds were successfully separated on the hybrid monolith in capillary LC (cLC), and high column efficiencies were achieved in all of the separations. In addition, as the amino groups could generate a strong EOF, the hybrid monolith was also applied in CEC for the separation of neutral and polar compounds, and a satisfactory performance was obtained. These results demonstrate that the poly(POSS-co-BDA) hybrid monolith is a good separation media in chromatographic separations of various types of compounds by both cLC and CEC.
An organic-inorganic hybrid monolith was prepared by a single-step ring-opening polymerization of octaglycidyldimethylsilyl polyhedral oligomeric silsesquioxane (POSS) with poly(ethylenimine) (PEI). The obtained hybrid monoliths possessed high ordered 3D skeletal microstructure with dual retention mechanism that exhibits reversed-phase (RP) mechanism under polar mobile phase and hydrophilic-interaction liquid chromatography (HILIC) retention mechanism under less polar mobile phase. The high column efficiencies of 110,000N/m can be achieved for separation of alkylbenzenes in capillary reversed-phase liquid chromatography (cLC). Due to the robust property of hybrid monolith and the rich primary and secondary amino groups on its surface, the resulting hybrid monolith was easily modified with γ-gluconolactone and physically coated with cellulose tris(3,5-dimethylphenylcarbamate) (CDMPC), respectively. The former was successfully applied for HILIC separation of neutral, basic and acidic polar compounds as well as small peptides, and the latter for enantioseparation of racemates in cLC. The high column efficiencies were achieved in all of those separations. These results demonstrated that the hybrid monolith (POSS-PEI) possessed high stability and good surface tailorbility, potentially being applied for other research fields.
This study introduces zwitterionic monolithic capillary columns intended for isocratic and gradient HILIC separations. Silica-based monolithic capillary columns (100μm×150mm) prepared by acidic hydrolysis of tetramethoxysilane in the presence of polyethylene glycol and urea were modified by a sulfoalkylbetaine zwitterion ([2-(methacryloyloxy)ethyl]-dimethyl-(3-sulfopropyl)-ammonium hydroxide) to HILIC stationary phase. The prepared columns were evaluated under the isocratic and gradient separation conditions using a standard mixture containing nucleic acid bases, nucleosides, and 2-deoxynucleosides. Mobile phases contained high concentration of acetonitrile (95-85%, v/v) and 5-50mM ammonium acetate or ammonium formate in the pH range of 3-6. The synthesized columns showed a long-term stability under the separation conditions while the high permeability and efficiency originating from dual structure of the silica monolith were preserved. The relative standard deviations (RSDs) for the retention times of tested solutes were lower than 2% under the isocratic conditions and lower than 3.5% under the gradient conditions.
A novel zwitterionic hydrophilic porous monolithic stationary phase was prepared based on the thermal-initiated copolymerization of N,N-dimethyl-N-(3-methacryl-amidopropyl)-N-(3-(sulfopropyl)ammonium betaine and ethylene glycol dimethacrylate. A typical hydrophilic separation mechanism was observed at a highly organic mobile phase (ACN >60%) on this optimized zwitterionic hydrophilic interaction chromatography (HILIC) monolithic stationary phase. Good permeability, stability, and column efficiency were observed on the final monolithic column. Additionally, a weak electrostatic interaction for charged analytes was confirmed in analysis of six benzoic acids by studying the influence of mobile phase pH and salt concentration on their retention behaviors on the obtained zwitterionic HILIC monolithic column. The optimized zwitterionic HILIC monolith exhibited good selectivity for a range of polar test analytes.
A novel, facile, highly flexible process was developed for the first preparation of well-controlled 3D skeletal polyhedral oligomeric silsesquioxane (POSS)-based functionalizable porous hybrid monoliths via ring-opening polymerization. This approach represents an ideal pathway for easy access to a series of hybrid monoliths with high separation efficiency in cLC.
Several imidazolium-based ionic liquids (ILs) with varying cation alkyl chain length (C(4)-C(10)) and anion type (tetrafluoroborate ([BF(4)](-)), hexafluorophosphate ([PF(6)](-)) and bis(trifluoromethylsulfonyl)imide ([Tf(2)N](-))) were used as reaction media in the microwave polymerization of methacrylate-based stationary phases. Scanning electron micrographs and backpressures of poly(butyl methacrylate-ethylene dimethacrylate) (poly(BMA-EDMA)) monoliths synthesized in the presence of these ionic liquids demonstrated that porosity and permeability decreased when cation alkyl chain length and anion hydrophobicity were increased. Performance of these monoliths was assessed for their ability to separate parabens by capillary electrochromatography (CEC). Intra-batch precision (n=3 columns) for retention time and peak area ranged was 0.80-1.13% and 3.71-4.58%, respectively. In addition, a good repeatability of RSD(Retention time)=<0.30% and ∼1.0%, RSD(Peak area)=<1.30% and <4.3%, and RSD(Efficiency)=<0.6% and <11.5% for intra-day and inter-day, respectively exemplify monolith performance reliability for poly(BMA-EDMA) fabricated using 1-hexyl-3-methylimidazolium tetrafluoroborate ([C(6)mim][BF(4)]) porogen. This monolith was also tested for its potential in nanoLC to separate protein digests in gradient mode. ILs as porogens also fabricated different alkyl methacrylate (AMA) (C4-C18) monoliths. Furthermore, employing binary IL porogen mixture such as 1-butyl-3-methylimidazolium tetrafluoroborate ([C(4)mim][BF(4)]) and 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C(4)mim][Tf(2)N]) successfully decreased the denseness of the monolith, than when using [C(4)mim][Tf(2)N] IL alone, enabling a chromatographic run to be performed with 1:1 ratio produced baseline separation for the analytes. The combination of ILs and microwave irradiation made polymer synthesis very fast (∼10min), entirely green (organic solvent-free) and energy saving process.
Comparisons of columns, column packings and column packing methods are made difficult and sometimes invalidated by differences and inadequacies in the test procedures used and the experimental data recorded. This paper reviews test procedures and recommends standards for a) the experimental and test parameters which must be recorded in order to enable comparisons to be made from laboratory to laboratory, b) the group of chromatographic parameters which best represent column performance for comparative purposes, with methods for their calculation, c) test solutes and eluents for some different types of packing materials. A computer program in BASIC is given which converts the experimental parameters into relevant chromatographic parameters.
Ionic liquids (ILs) are organic salts that are liquid at ambient temperatures. Ionic liquids have emerged as a new class of solvents for practical applications due to their unique combination of low volatility, chemical stability, high conductivity, wide electrochemical window, ability to dissolve organic and inorganic solutes and gases, and tunable solvent properties. In polymer science ionic liquids are used as solvents for polymerization processes and as components of polymeric materials. In this review the advantages and limitations of application of ionic liquids as solvents for polymerization processes are critically discussed, with special emphasis on results published within last 5 years.
A simple single-step thermal-treatment "one-pot" approach for the preparation of organic-silica hybrid capillary monolithic columns is described. In this improved method, the cross-linker vinyltrimethoxysilane (VTMS) was replaced by 3-methacryloxypropyltrimethoxysilane (γ-MAPS), which is more active in polymerization reactions, and only one thermal treatment step was required in the preparation of hybrid monoliths. Two zwitterionic organic-silica monolithic columns were successfully synthesized by using [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (MSA) and 2-methacryloyloxyethyl phosphorylcholine (MPC) as the organic monomers. The effects of the tetramethoxysilane (TMOS)/γ-MAPS molar ratio, content of monomer, composition of porogenic solvent, and reaction temperature on the morphologies of the hybrid monoliths were investigated. The MSA-silica and MPC-silica hybrid monolithic columns exhibited good permeability and good mechanical stability. The monolithic columns were used for the separation of polar compounds by capillary hydrophilic-interaction chromatography (cHILIC). A typical HILIC retention mechanism was observed at higher organic solvent contents (>50% ACN). The MSA monoliths were further investigated in the separation of various neutral, basic, and acidic analytes, as well as small peptides, by capillary liquid chromatography (cLC), and high efficiency and satisfactory reproducibility were achieved. In addition, the analysis of a tryptic digest of bovine serum albumin (BSA) by cLC tandem mass spectrometry (cLC-MS/MS) with an MSA monolith further demonstrated its potential in the separation of biological samples.
The rate constants of propagation and termination of methyl methacrylate (MMA) in the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate were measured using the pulsed laser polymerization technique across a range of temperatures, and Arrhenius parameters were calculated for the rate of propagation at ionic liquid concentrations of 0, 20, and 50% v/v. Point estimates for these values are A = 2.4 x 10(6) L mol(-1) S-1 (0% v/v ionic liquid), 2.1 x 10(6) L mol(-1) s(-1) (20% v/v), and 2.5 X 10(6) L mol(-1) s(-1) (50% v/v) and E-A = 22.1 kJ mol(-1) (0% V/V), 21.0 kJ mol(-1) (20% v/v), and 20.4 M mol(-1) (50% v/v). The decrease in activation energy leads to large increases in the rate of propagation. In addition, the rate of termination decreases by an order of magnitude as the ionic liquid concentration is increased to 60% v/v. The increase in propagation rate was attributed to the increased polarity of the medium, while the decrease in the termination rate is due to its increased viscosity.
Fourteen commercially available particle-packed columns and a monolithic column for hydrophilic interaction liquid chromatography (HILIC) were characterized in terms of the degree of hydrophilicity, the selectivity for hydrophilic-hydrophobic substituents, the selectivity for the regio and configurational differences in hydrophilic substituents, the selectivity for molecular shapes, the evaluation of electrostatic interactions, and the evaluation of the acidic-basic nature of the stationary phases using nucleoside derivatives, phenyl glucoside derivatives, xanthine derivatives, sodium p-toluenesulfonate, and trimethylphenylammonium chloride as a set of samples. Principal component analysis based on the data of retention factors could separate three clusters of the HILIC phases. The column efficiency and the peak asymmetry factors were also discussed. These data on the selectivity for partial structural differences were summarized as radar-shaped diagrams. This method of column characterization is helpful to classify HILIC stationary phases on the basis of their chromatographic properties, and to choose better columns for targets to be separated. Judging from the retention factor for uridine, these HILIC columns could be separated into two groups: strongly retentive and weakly retentive stationary phases. Among the strongly retentive stationary phases, zwitterionic and amide functionalities were found to be the most selective on the basis of partial structural differences. The hydroxyethyl-type stationary phase showed the highest retention factor, but with low separation efficiency. Weakly retentive stationary phases generally showed lower selectivity for partial structural differences.
An inorganic-organic hybrid monolithic capillary column was synthesized via thermal free radical copolymerization within the confines of a capillary using a polyhedral oligomeric silsesquioxane (POSS) reagent as the inorganic-organic hybrid cross-linker and a synthesized long carbon chain quaternary ammonium methacrylate of N-(2-(methacryloyloxy)ethyl)-dimethyloctadecylammonium bromide (MDOAB) as the organic monomer. The preparation process was as simple as pure organic polymer-based monolithic columns instead of using POSS as the nanosized inorganic-organic hybrid blocks (cross-linker) of the monolithic matrix. The pore properties and permeability could be tuned by the composition of the polymerization mixture. The characterization and evaluation results indicated that the synthesized MDOA-POSS hybrid monolith possessed the merits of organic polymer-based monoliths and silica-based monoliths with good mechanical and pH (pH 1-11) stabilities, which may be attributed to the incorporation of the rigid nanosized silica core of POSS. Column efficiencies of 223 000 and 50 000 N/m were observed in capillary electro-driven chromatography (CEC) and mu-HPLC, respectively. Peptides and standard proteins were baseline separated by this hybrid column in CEC and mu-HPLC, respectively, as well. The separation of bovine serum albumin (BSA) tryptic digest was also attempted to show its potential application in proteome analysis.
Some of the latest developments in the investigations of the chemistry of cubic polyhedral oligosilsesquioxanes were reviewed. The review focued on investigating the chemistry of those compounds that were based on the (RSiO 3/2)8 formula. The general structure of RSiO 3/2)8 revealed some of the significant features of these molecules, including the siloxane cage size and the distribution of the eight pendant arms from the cube in a three-dimensional arrangement. The review also focused on on the synthesis, properties, and applications of molecular T 8R8 compounds in place of their properties and applications within polymeric materials. The findings of the review focused on the synthesis of T8 POSS, which were earlier unknown species and new syntheses of known species.
A novel zwitterionic hydrophilic porous poly(SPV-co-MBA) monolithic column was prepared by thermal co-polymerisation of 1-(3-sulphopropyl)-4-vinylpyridinium-betaine (4-SPV) and N,N'-methylenebisacrylamide (MBA). An HILIC/RP dual separation mechanism was observed on this optimised poly(SPV-co-MBA) monolithic column and the composition of the mobile phase corresponding to the transition from the HILIC to the RP mode was around 30% ACN in water. Higher hydrophilicity was achieved on this novel monolithic column compared to the poly(N,N-dimethyl-N-methacryloxyethyl-N-(3-sulphopropyl)ammonium betaine-co-ethylene dimethacrylate) monolithic column. Permeability studies showed slight swelling and/or shrinking with mobile phases of different polarity. As might be anticipated, a weak electrostatic interaction for charged analytes was also observed by studying the influence of mobile phase pH and salt concentration on their retention on the poly(SPV-co-MBA) monolithic column. The final optimised poly(SPV-co-MBA) monolith showed comparable selectivities to commercial ZIC-pHILIC phases for polar test analytes. Fast separation of five pyrimidines and purines was achieved in less than 1 min due to the high permeability of the monolithic column. Additionally, baseline separation of nine benzoic acid derivatives was also observed using either a pH or ACN gradient.
Monolithic columns for capillary hydrophilic interaction liquid chromatography (HILIC) were prepared in fused-silica capillaries by radical co-polymerization of [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide and ethylene dimethacrylate in various binary and ternary porogen solvent mixtures with azobisisobutyronitrile as the initiator of the polymerization reaction. Columns showed mixed separation modes: reversed-phase (RP) in water-rich mobile phases and HILIC at high concentrations of acetonitrile (>60-80%) in aqueous-organic mobile phases. A continuous change in retention was observed at increasing concentration of water in acetonitrile, giving rise to characteristic U-turn plots of retention factors versus the concentration of water in the mobile phase, with minima corresponding to the transition between the mechanisms controlling the retention. The selectivity of organic polymer monolithic columns for HILIC separations can be varied by adjusting the concentration of sulfobetaine monomer and the composition of the porogen solvent in the polymerization mixture. Under HILIC conditions, the monolithic capillary sulfobetaine columns show separation selectivities for polar phenolic acids similar to those of a commercial silica-based sulfobetaine ZIC-HILIC column, which, however, has limited selectivity in the RP mode due to lower retention.