Figure - available from: Journal of The Electrochemical Society
This content is subject to copyright. Terms and conditions apply.
Top: illustration of a Li-ion Pouch cell consisting of graphite anode and NMC cathode. Middle: representative cell designs for energy-type and power-type Li-ion batteries using the same Graphite/NMC electrochemistry. Down: summarized advantages and disadvantages of pouch Li-ion cells for practical applications.
Source publication
The number of publications in electrochemical energy storage has increased exponentially in the past decades, focusing mostly on materials science. The electrochemical process controlling the observed overall performances is often not well discussed. This article highlights the importance of understanding rate-limiting steps in the electrochemical...
Similar publications
With the exponential expansion of electric vehicles (EVs), the disposal of Li-ion batteries (LIBs) is poised to increase significantly in the coming years. Effective recycling of these batteries is essential to address environmental concerns and tap into their economic value. Direct recycling has recently emerged as a promising solution at the labo...
Citations
... Solid-state polymer electrolytes have garnered a lot of attention due to its potential in solidstate electrochemical devices-which span a extensive range of applications, including chemical sensors, fuel cells, super capacitors, and rechargeable batteries 1,2,3,4 . Solid polymer electrolytes (SPEs), as compared to liquid electrolytes, have an array of features. ...
... It is thought that the Mg 2+ ions' effect on HFP stretches the PVDF bonds to ideal values, encouraging the shift from the crystalline to the amorphous phase. 25 The vibration band shifts from 784-813 cm -1 to 813-927 cm -1 as the concentration drops when PVDF-co-HFP is complexed with Mg(CF 3 ...
Solution casting technique was cast-off to create a novel kind of magnesium ion conductive nanocomposite polymer electrolyte membrane. The films include dissimilar weight percentages of Al2O3 nanofillers embedded in the congregation polymer PVDF-co-HFP, containing magnesium triflate Mg(CF3SO3)2. The distinctive crystalline phases of the polymer and its segment dynamics are considerably changed by changes in the component content of these SPEs. The structural morphology of these films were characterized by the techniques such as FTIR, DSC, SEM, and XRD. Fourier transform infrared spectroscopy (FTIR) was used to affirm the chemical composition of the polymer electrolyte membrane, Differential scanning calorimetry (DSC) was used to verify a decline in melting temperature, Scanning electron microscopy (SEM) was used to affirm the exterior morphology of the film, and Xray diffraction (XRD) was used to ensure the drop in crystallinity. It was observed that 8wt% of Al2O3 exhibits the best among them. The addition of nano filler was found to trigger the band of C–O–C stretching to move to a lesser wave number and the strength of the peaks to drop, signalling that the films' crystalline nature had changed to an amorphous one.
... Electrochemical energy storage systems play an extremely important part in a wide variety of technological applications, including but not limited to supercapacitors, electrochemical devices, sensors, fuel cells, and many more. [1][2][3][4][5][6] In the middle of the technologies that are developing today, it is anticipated that there will be an even bigger need for rechargeable batteries that have high specific energy, high power, give excellent metal surface stability, and that have high electrochemical stability. [7][8][9] Multivalent ion-based secondary batteries for large-scale stationary energy storage applications have been developed during the last two decades due to their abundance, extensive distribution, chemical stability, low cost, and environmental friendliness. ...
In this particular study, porous structured solid PVDF-co-HFP: MgTf3 polymer electrolytic membranes are made by using the solution cast method. PVDF-co-HFP is a material that has outstanding performance and has been extensively used in the preparation of solid polymer electrolyte membranes (SPEM). The use of SPEM with high porosity structure has the potential to increase the conductivity, which may result in enormous applications in the development of future batteries. The addition of the inorganic salt particles (Magnesium trifluoromethanesulfonate (MgTf3)) and coating of the SPEM with a variety of polymer media for the manufacture of storage devices are just two of the many methods that have been tried in an effort to decrease the pore size and the number of pores in the SPEM. The current research was successful in decreasing pores’ size and increasing the amorphous nature of the solid polymer membrane with the addition of the metal salt particles as an inorganic filler. The chemical structure of the prepared SPEM was investigated using Fourier transform infrared spectroscopy (FTIR), and a scanning electron microscope (SEM) was utilized to explore the surface morphology and to find pores in the SPEM. X-ray diffraction (XRD) analysis was used to confirm the surface morphology of the PVDF-co-HFP membrane and the PVDF-co-HFP-MgTf3. A differential scanning calorimetry (DSC) investigation was carried out the determining the electrochemical consistency of the PVDF-coHFP and PVDF-co-HFP: MgTf3 membranes. According to the research, inorganic salt particles can make PVDF-coHFP: MgTf3 membranes less porous, increase the conductivity of ions and make the membrane more stable when it is filled with electrolytes and electrodes.
The consistency of cathode particles plays a pivotal role in battery performance.
