Fig 4 - available via license: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International
Content may be subject to copyright.
Examples of the available retrograde suture passers. The 18-gauge spinal needle has the smallest diameter.
Source publication
Suture passing devices are frequently used for subscapularis tendon repair. However, some of these devices can further damage the tendon by creating a larger tear. Use of an 18-gauge spinal needle as a suture passer helps eliminate damage to the tendon. By using its smaller diameter, the needle prevents tendon cut-through and enhances the precision...
Context in source publication
Context 1
... The use of spinal needle for subscapularis repair helps to prevent further injury to the tendon. When comparing the modern retrograde suture passing devices available in the market, the diameter of the spinal needle is the smallest (Fig 4). The small diameter helps improve the precision of suture placement when repairing the tendon. ...
Similar publications
Purpose:
The purpose of this study is to describe rotator cuff muscle stiffness in patients with different degrees of rotator cuff tear (RCT) severity and to assess its predictive ability for RCT reparability.
Methods:
One hundred and thirty-three consecutive patients who were scheduled to undergo arthroscopic shoulder surgery were prospectively...
Rotator cuff tears are a common cause of pain and disability among adults. Partial tears are usually treated conservatively. Complete tears might be treated conservatively in some cases; however, surgical repair is often performed in selected cases and situations where conservative treatment fails to restore function and pain relief. In addition, s...
Subscapularis tears have been found to occur in the setting of subcoracoid impingement and are related to the narrowing of the coracohumeral interval. The advancement of arthroscopic techniques has allowed for improved identification and treatment of this historically overlooked pathology. Challenges of arthroscopic subscapularis treatment include...
Citations
... Therefore, we could suggest medical device companies to use a flathead pin to replace the current needle tip. Of course, other puncture tools can also be used (16). Needle breakage may also be avoided with the progress of science and technology; new tools and methods should appear, including automated-assisted suture passage (17,18). ...
Introduction
Suture passer needle, as one of commonly used instrument in the arthroscopic rotator cuff repair, often breaks at the notch of the needle, which originally was designed to facilitate suture with thread. Our study aimed to evaluate the suture failure rate and stitch success rate between intact suture needle and broken needle and explore the mechanism of the needle breakage and achieving better future designs.
Materials and methods
From 2017 to 2021, consecutive 437 shoulders (11 cases were bilateral) underwent arthroscopic repair for full-thickness rotator cuff tear at the authors’ institution. The breakage of needles was recorded. Finite elements analysis and mechanical test were utilized to compare stress distribution, puncture performance, and loaded puncture performance between the broken needle and the intact needle.
Results
We identified 19 consecutive patients for whom the needle tip of the TruePass™ suture passer was broken in the 437 shoulder surgeries. Based on the finite element analysis of Abaqus, around the tip and the notch of the intact needle was a large stress concentration. The average puncture force required by intact needle tip and the broken tip is 61.78N and 78.23N respectively. While the intact tip with notch is easier to break than the broken tip.
Conclusions
The notch of the needle is a weak point in mechanics. The broken needle without the notch still has good tendon piercing and thread passing ability. The notch of needle may be not necessary, and the tip of the needle should be modified.
The main method for arthroscopic repair of the subscapularis is repair with suture anchors. The surgeon generally establishes the anterior and anterolateral operation portals to complete anchor implantation and suture passing, respectively. The single–operation portal technique has been developed recently. However, in the traditional single–operation portal technique, the suture device and grasper are difficult to operate simultaneously. In addition, with the traditional rotator cuff suture device, it is easy to cause further iatrogenic injury to the rotator cuff because of its larger diameter. Therefore, we describe a modified single–operation portal technique for suture passing percutaneously with a spinal needle taking into account the shortcomings of existing techniques. Our modified technique avoids the use of traditional suturing devices and effectively avoids further damage to the rotator cuff. The use of a single operation portal makes the operation more minimally invasive and simple and effectively avoids the problem of interference between the suture device and grasper in the same portal. The entire operational process does not require the use of costly consumables, resulting in increased cost-effectiveness and a significantly reduced operating time. In conclusion, our modified technique achieves the use of a single operation portal to suture the subscapularis through spinal needle suture passing, which has good clinical value.
